How To Change The Needle on a Brother Sewing Machine? Best Tips in 2023
Do you want to know how to change the needle on a brother sewing machine? If yes, then take a PAUSE. In this article, we will let you know about it.
We aligned the needle on our Brother sewing machine by adjusting the setting to its original, factory-default configuration. In addition, you will learn how to adjust the needle position on your Brother sewing machine by reading this article.
When changing the needle, most sewing machines will have a door or compartment on the side that can be opened. You will need to consult the handbook that came with your device to find out precisely where it is and how to access it.
After the compartment has been opened, the old needle may be removed, and a new one can be screwed. Before you begin stitching again, check to see that the new needle is positioned so that the right side faces up. Click here to watch this video about changing the needle on a brother sewing machine.
How To Change The Needle on a Brother Sewing Machine?
Assuming you are interested in a detailed guide on changing the needle on a brother sewing machine.
- Ensure that your device is switched off and disconnected before beginning this procedure.
- Raise the presser foot lever, and then release the needle by rotating the handwheel toward you until the mark is aligned with the needle clamp screw.
- Loosen the screw that secures the needle clamp, and then remove the needle.
- Insert the replacement needle and ensure the flat side is towards the rear. Tighten the clamp screw tightly by the hand, then use a wrench or pliers to turn it another 1/4 to 1/2 turn.
- For general-purpose stitching, we suggest using authentic Brother sewing machine needles, available in sizes 65/9, 70/10, 80/12, 90/14, and 100/16. Embroidery needles are also available in sizes 75/11. For the greatest results, we recommend using genuine Brother sewing machine needles.
- If you want to reuse a needle of the same size, check to be sure it hasn’t been broken or bent before inserting it. In addition, check to see that the tip of the new needle is completely inserted into the eye of the shaft until it reaches its limit (do not force).
- Before removing workpieces beneath the feed dogs, move the wheel by hand one full revolution counterclockwise in the anticlockwise direction. This will drop the feed dogs entirely out of place (this will prevent fabric damage).
- Raise the presser foot lever and gently twist the handwheel toward you until the mark on the face plate is aligned with the index mark (the needle should be in the highest position),
- Then, carefully rotate the handwheel until the take-up lever reaches its top position. Finally, the thread tension discs are opened as far as feasible without coming into contact with one another (or release spring).
Here are some short steps on how to change the needle on a brother sewing machine:
- Stop Brother’s sewing machine
- Find the stitch selection key and press the (+) side
- Engage the machine and release the (+) side.
- The Brother sewing machine needle must be reset to the middle position.
How Do You Align the Needle on a Brother Sewing Machine?
The queries determine this section that the client asks. In this section, we will go through the needle alignment process and adjust the needle’s location.
You may take a few different approaches if you need help properly positioning the needle on your Brother sewing machine. First, check that the needle is securely positioned inside the needle bar.
If not, loosen the clamp holding the needle bar and insert the needle, so the flat side faces up.
After that, the clamp should be tightened until it is secure. Next, verify that the needle is positioned appropriately inside the holder by examining it closely. Finally, it should be inserted in such a way that the tip of the needle is pointing in the direction of the rear of the machine.
If it is not, take out the holder and put it back in the machine so that the tip of the needle points in the appropriate direction.
Lastly, take a look at the tension disc that you have. It may be necessary to readjust the alignment if the component is not screwed on with sufficient force.
Unscrew it partially, reattach it and tighten the screws until it fits securely. When you’ve given all these solutions, your Brother sewing machine should be back up and running in no time!
Where Does the Needle Drop on a Sewing Machine?
You may stop stitching on certain sewing machines using Needle Drop or Needle Down. With this option, the needle remains in the down position even after the machine is turned off. When working on large projects like quilts, it is helpful to have the ability to elevate the presser foot and move the cloth to get the best results.
Final Verdict:
In this article, we have told you how to change the needle on a brother sewing machine. Holding the plus side of the key and letting go when you turn on the machine will realign the needle to the default centre. You can do the same on the negative side to move the needle up or down. If you still have any questions, contact us without any hesitation.
